澳门太阳集团0638sss

服务热线: 400-117-8816
           13406879330

专注于扭剪型电动扳手、扭剪型手动扳手、定扭矩电动扳手、扭矩倍增器的研发与生产

热门关键词: 电动扳手能更快速地完成螺栓链接吗? 重型应用螺栓完成平安快速扭紧和拆卸的处理计划 工地用的电动扳手哪里有卖的,哪家质量好? 电动扭矩扳手必需恪守的硬性规则

当前位置:首页>新闻中心>数显测力计出现测量不准原因!

数显测力计出现测量不准原因!

来源:澳门太阳娱乐集团官网 日期:2020-02-04 发布人:admin

不少测力计的使用者在用数显测力计的时候通常会遇到的一个问题,那就是数显测力计出现测量不准确,大部分测力计用户都不明白其中的原因,下面就由实干数显测力计小编来为大家介绍下数显测力计出现测量不准原因。

Many users of the dynamometer usually encounter a problem when using the digital display dynamometer, that is, the measurement of the digital display dynamometer is not accurate, most of the users of the dynamometer do not understand the reasons. The following is a small part of the dry digital display dynamometer to introduce the reasons for the inaccurate measurement of the digital display dynamometer.
其实导致数显测力计测量不准原因主要有两个:
In fact, there are two main reasons for inaccurate measurement of digital dynamometer:
一、没有正确的使用数显测力计:
1、 No proper use of digital dynamometer:
1、对数显测力计造成*大伤害的是,在测试的时候千万不能超出它的测量范围,不能做推或拉两种方向以外的负荷试验。
1. What does great harm to the digital dynamometer is that it must not exceed its measuring range during the test, and it is not allowed to conduct load test beyond push or pull directions.
2、当测试杆在未接任何测试头时候,不能将被测负荷直接作用在测试杆端。
2. When the test rod is not connected with any test head, the measured load cannot be directly applied on the end of the test rod.
3、请不要使用损坏或弯曲变形的测试头,这样造成误差是在所难免的。
3. Please do not use the damaged or bent test head, which will inevitably cause errors.
4、请不要将数显测力计经常用在测量超过*大测试负荷的负载,否则负荷检出机构的弹性力将会逐渐劣化,导致检出的负荷值无法达到要求的准确度等级。
4. Please do not use the digital display dynamometer to measure the load exceeding * large test load, otherwise the elastic force of the load detection mechanism will gradually deteriorate, resulting in the detected load value unable to reach the required accuracy level.
5、在使用数显式数显测力要注意,使用之前首先检测电池电压是否正常,如果欠压请及时充电,否则测量会出现偏差。
5. Pay attention to the use of digital display force measurement timing. Before use, first check whether the battery voltage is normal. If the battery voltage is under voltage, please charge it in time, otherwise the measurement will be biased.
二、没有定期的对数显测力计进行保养和维修:
2、 There is no regular maintenance and repair for the digital display dynamometer:
1、由于数显测力计是用电能供应能量的,因此如果长期不使用时,应定期给测力计充电。
1. Since the digital display dynamometer uses electric energy to supply energy, if it is not used for a long time, it should be charged regularly.
2、每次使用玩数显测力计就把它装进箱子里面放到室温的地方,千万不能放在有阳光的地方暴晒。
2. Every time you use a digital dynamometer, put it in a box and put it in the room temperature. Never put it in the sun.
3、数显测力计存放的地方如果是潮湿、不通风的,那麽就会造成仪器遭到锈蚀、损坏。
3. If the place where the digital dynamometer is stored is damp and airless, the instrument will be rusted and damaged.
如果你觉得以上两种办法还不能解决数显测力计测量不准原因的话,可以来电反馈给我们,我们可以帮你解决哦!
If you think the above two methods can't solve the problem of inaccurate measurement of digital display dynamometer, you can call us for feedback and we can help you solve it!

澳门太阳集团0638sss-澳门太阳娱乐集团官网